¶ Contents
¶ 1. Machine
Protect your hands, wrists and fingers.
Do not put any of your body parts inside the machine or anywhere near the head during operation.
| A | Camera | Shows actual view of material to design. |
| B | Pressure Adjuster | Adjusts the pressure of the engraving tool. |
| C | Spindle | Secures the tool for engraving.
※To change tools, use a 2mm T-wrench. |
| D | Tool holder | Storage for tools. |
| E | Status Indicator | Shows the status of the device via blinking interval |
| F | Control Panel | Controls the power button and the manual control for regulating engraving operations. |
| G | Emergency Switch | Stops the machine during emergency. |
| H | Power Switch | Switches the power on/off. |
| I | USB Port | To connect USB cable to PC. |
| J | Power Port | To connect power adapter to supply power to the machine. ※Use a grounded outlet only. Do not plug the machine into an ungrounded outlet. |
| K | IO Port | To connect the dust connector. |
¶ 2. Clamp
¶ 1) Flatbed Clamp
Place the material on the flatbed then secure it by using the clamps provided (see clamps below). The clamps are used to secure the material to the flatbed so that the material stays in place during engraving or cutting process. The number of clamps to be used may vary depending on the size and/or shape of the material.
※See picture for reference.
| L-wrench(4mm) (CP-L40) |
 |
1EA | For tightening/unscrewing the bolt. |
| Push clamp |  |
2EA | To hold materials in place. |
| Push clamp |  |
2EA | To hold materials in place. |
| Knob (M5x12mm) |
 |
2EA | To secure the clamp set. |
| Knob (M5x25mm) |
 |
2EA | To secure the clamp set. |
| Knob (M5x30mm) |
 |
2EA | To secure the clamp set. |
| Knob cap |  |
2EA | Cap for knob: Used with **M5x25mm knob.** |
| Bolt (M5x10mm) |
 |
5EA | To secure the clamp set. |
| Bolt (M5x18mm) |
 |
5EA | To secure the clamp set. |
[How to secure the material with press clamps]
For thin material:
Both press and push clamps can be used to secure thin materials. Use the knobs to attach the clamps to the flatbed. Screw the knobs down to the flatbed to secure the material in place. Take note that the position of the clamps and the number of clamps to be used may depend on the size and shape of the material. It may also depend on user’s preference.
|
 |
| Press clamp with knob | Push clamp with knob |
For thick material:
- Assemble the press clamp. Insert the M5x25mm knob into the hole of the press clamp then screw the cap.
- Place the material on the clamp.
- Place the assembled press clamp on top of the material (in a horizontal position). The clamp must be placed on the same level as the material surface.
- Attach the press clamp to the flatbed. Insert the M5x30mm knob into the press clamp then screw the knob down to secure the material to the flatbed.
- Secure the sides of the material. Use two or more clamps to secure the material. Be sure to screw the knobs down to the flatbed so the material stays in place.
¶ Height Adjustable Clamp
Height adjustable clamp is used to adjust the height of your material.
| Height adjustable clamp (CP-252) |
 |
1EA | To adjust the height of the clamp. |
- Turn the Height Adjustable clamp clamping knob counterclockwise to detach the Multipurpose Clamp.
- Turn the clamping knob counterclockwise to detach the height adjustable clamp.
- Attach the multipurpose clamp then fasten it by turning the clamping knob clockwise.
¶ L-Type Clamp
※Optional device; sold separately
Used to secure locks to the flatbed (work area).
[How to install the jig]
- Screw the M5 bolts to the flatbed with an L-wrench.
- Match the size of the lock (material) to the clamp. To adjust, reposition the upper part then screw the bolts to the flatbed.
¶ 2) Multipurpose Clamp
The package includes a multifunctional clamp that is easily assembled, disassembled and transformed into 3 different types of clamps. It can be adjusted according to the height of the material, and can be expanded according to the material’s thickness, size, and shape. This single clamp alone makes engraving on various materials possible without the use of any additional clamps.
¶ How to secure the material in place
Use the clamping knob to secure your material in place. To loosen or widen the clamp, turn the clamping knob counterclockwise; to fasten it, turn the knob clockwise.
Marks may be left on the material if fastened tightly.
¶ How to position the material
Use the vertical ruler bar as an alignment guide to help you position and align your material to the clamp with ease and accuracy. Properly place your material on the clamp then check the alignment.
¶ How to secure the material with irregular shape in place
Use the clamping pins to firmly hold materials with irregular shapes in place. To secure the clamping pins to the clamp, simply insert the pins into the pin holes then fasten them.
¶ How to adjust the height of the clamp
Below are instructions on how to adjust the height of the clamp according to the thickness of the material.
- Turn the clamp over (to the back) then screw the bolts (M4x20mm). ※Use a 3mm L-wrench to screw the bolts.
- Turn the clamp over (to the front) then pull out the clamp base.
- Remove the clamping pins then secure the material to the V groove of clamp without clamp base. (See picture below for reference).
¶ Height Adjustable Clamp
Height adjustable clamp is used to adjust the height of your material.
| Height adjustable clamp (CP-252) |
|
1EA | To adjust the height of the clamp. |
- Turn the Height Adjustable clamp clamping knob counterclockwise to detach the Multipurpose Clamp.
- Turn the clamping knob counterclockwise to detach the height adjustable clamp.
- Attach the multipurpose clamp then fasten it by turning the clamping knob clockwise.
¶ How to adjust the height of the clamp
※Optional device; sold separately
Below are instructions on how to adjust the height of the clamp according to the thickness of the material.
| Spacer block (CP-250S) |
 |
1EA | To adjust the height of the clamp. |
- Turn the clamping knob counterclockwise to detach the clamp.
- Turn the clamp over (to the back) then screw the bolts (M4x20mm). ※Use a 3mm L-wrench to screw the bolts.
- Once the bolts are removed, turn the clamp over (to the front) then pull out the clamp base. Then, reassemble the spacer block to pin.
※ After secure the spacer block, then secure the material to the V groove of clamp.
- Screw the spacer block fixing bolt (M4x20mm). ※Use a 3mm L-wrench to unscrew the bolts.
- Secure the base clamp by attaching it to the pins.
- Turn the clamp over (to the back) then unscrew the bolts (M4x40mm).
※Use a 3mm L-wrench to unscrew the bolts.
※ To assemble or reassemble the spacer block, use the appropriate bolts. Be sure to use and secure the spacer block using the correct type of bolts.
 |
 |
| Spacer block fixing bolt- M4x20mm | Clamp base fixing bolt- M4x40mm |
¶ Optional items for Multipurpose Clamp
¶ 1. Pin clamp
※Optional device; sold separately
| Pin clamp (CP-80) |
 |
1SET | To hold materials with different shapes in place. |
| Pin (CP-172) |
 |
5EA | To hold materials with irregular shapes in place. |
| Wrench bolt (M4x6) |
 |
5EA | To fasten the clamp. |
| L-wrench(3mm) (CP-L30) |
 |
1EA | For tightening/unscrewing the bolt. |
¶ 2. Cutlery clamp
※Optional device; sold separately
| Cutlery clamp (CP-83) |
 |
1SET | To firmly hold spoons in place. |
¶ 3. Watch adapter
※Optional device; sold separately
| Watch adapter (CP-84) |
 |
1SET | To firmly hold watch in place. |
| Wrench bolt |  |
5EA | To fasten the adapter. |
| L-wrench(3mm) (CP-L30) |
|
1EA | For tightening/unscrewing the bolt. |
¶ 4. Bracelet adapter
※Optional device; sold separately
| Bracelet adapter (CP-85) |
 |
1SET | To firmly hold bracelets in place. |
| Pin |  |
4EA | To secure the adapter. |
¶ 5. Bar necklace adapter
※Optional device; sold separately
| Bar necklace adapter (CP-166) |
 |
1SET | Jig for holding materials with narrow width (about 2-3mm) in place. (Used for securing pendants, bar necklaces, etc.) |
| Pin | |
4EA | To secure the adapter. |
*Materials like bar necklaces or pendants may come off easily when attaching to the jig.
Press the material with your finger to secure it to the jig and be sure to not let your finger get caught while pressing.
¶ 6. Curved tag adapter
※Optional device; sold separately
| Curved tag adapter (CP-182) |
 |
1SET | Jig for holding curved materials in place. (Used for securing curved pendants, chain bracelets, etc.) |
| Pin | |
4EA | To secure the adapter. |
¶ 3. Keypad
| Display | Status display | ||
| Operation Buttons | Activate the operations intended to perform | ||
 |
Direction Key (X,Y/Z) |
Engraving area adjustment  (X) Moves X axis  (Y)(Z) Moves Y/Z axis ※Axis movement can be changed by using the operation buttons. |
|
 |
Vacuum ON/OFF | Chip collector power button • Automatic control: The device starts automatically once the engraving operation begins and stops automatically once the engraving operation is completed. • Manual operation: Automatic control is deactivated if the device is manually switched on. Once the engraving operation is completed, the device should be manually turned off. ※ We strictly advise our users to use the Chip collector during engraving operation for safety. The Chip collector prevents exposure form harmful inhalable particles and debris like metal chips and dusts which may cause eye injury if they get stuck in the eye or respiratory problems if inhaled. |
|
 |
Start | Start marking button • Start marking: Long-press (for 2 seconds) the [Start] button to start marking. • Repeat marking: Press the [Start] button to finish marking, then double-press (tap twice) the [Start] button to repeat marking. • Menu: Press OK when using the menu. |
|
 |
Menu | Enter the menu mode | |
 |
Stop | Stops/cancels marking | |
¶ 4. Menu
To enter Menu mode, press button. Select a menu item using the and buttons then press button to enter the menu item.
| 1. Tool Change | Changes the tool. | |
| 2. Select Origin | Sets the current position to the clamp origin. | |
| 3. Calibration | 1. Touch Sensor | Adjusts touch sensor settings. |
| 2. Probe | Adjusts probe settings. | |
| 4. Measure Z-Ref | 1. Height Only 2. Horizontal(X) Slope 3. Vertical(Y) Slope 4. Plane(XY) Slope *In rotary mode, only [1. Height Only] is enabled. |
|
| 5. Adjust Brightness | 1. Status LED | Adjusts status LED brightness |
| 2. Inside LED | Adjusts inside LED brightness | |
| 3. Pointer | Adjusts focus laser pointer brightness | |
| 6. Vacuum Setup | Sets the Chip collector function. -Set to automatic control. -Set the Chip collector type: Dry/wet type |
|
| 7. Tool-Pos Recording | Records your current location; set whether to activate or not. | |
| 8. Auto Zref on Repeat | Sets Auto Zref method for repetitive engraving: 1. No measurement 2. Height measurement 3. Height measurement + area check |
|
¶ 5. Display
The display shows the status, functions, mode, and check messages. Icons are displayed differently depending on the selected function. The four buttons at the bottom represent different functions and each function vary depending on the selected mode.
¶ 1) Standby-Flat
| Status | ||
|---|---|---|
 |
Bluetooth | Icon appears when Bluetooth is activated |
 |
Auto Zref on Repeat |  : No measurement : Height measurement only : Height measurement + area check |
 |
Chip collector Power | Chip collector ON/OFF: Icon does not appear when OFF |
 |
Focus Pointer | Laser pointer ON/OFF |
| XY:#1-C | X-Y Origin | X-Y origin •[#1]: Clamp No. (1-5) •[C]: Origin No. (C: Center; origin No.: 1-8) |
| Mode | ||
|---|---|---|
 |
Left-top origin | Moves the tool to the position saved in the “Left-top” button and sets the position as origin |
 |
Center origin | Moves the tool to the position saved in the “Center” button and sets the position as origin |
 |
Tool change | Switches to tool change mode |
 |
Auto focus | Activates camera auto focus position • Auto moves to view position after height measurement • Refreshes the camera display at MagicEngrave. ※Variety of features available for use once MagicEngrave software is enabled. |
¶ 2) Move Mode
Press one of the buttons in the [STANDBY] mode to activate [MOVE].
| Message | |
|---|---|
| X-Y Position | The message on display varies depending on the Y-axis mode: •Y→Y: X-Y axis position •Y→Z: Z-axis position •Y→A: A-axis position |
| Mode | ||
|---|---|---|
 |
Standby Mode | • Switches to the STANDBY mode • Switches automatically to [STANDBY] mode if not in use for 10 seconds. Press any buttons to activate [MOVE] mode. |
 |
Save Origin | Saves the current position as the XY origin *Short-press: Temporary save *Long-press: Permanent save  Y-axis movement mode: Save XY Origin Z-axis movement mode:  Save Z Origin |
|
Laser Pointer | Turns ON/OFF the laser pointer |
|
UP-DOWN Button Settings | The mode changes in sequence (Y-axis → Z-axis → Y-axis) in a loop whenever the button is clicked. |
¶ 3) Engraving mode
 |
Engraving Speed Control | Reduces engraving speed by 1mm/s whenever the button is pressed. |
 |
Increases engraving speed by 1mm/s whenever the button is pressed. |
¶ 4) Pause
| Mode | ||
|---|---|---|
 |
Return back to Previous position | Returns back to the previous position and resumes engraving. |
|
Tool Change | Switches to tool change mode |
 |
Resume | Resumes engraving. |
¶ 6. Status Indicator
The status indicator is placed at the bottom left side and bottom right side of the machine. It is used to indicate the status of the device.
The machine displays flashing or blinking lights to show its current status. The lights displayed indicate the following status:
| Status | Blinking Interval |
| Waiting |  |
| Engraving | |
| Operating |  |
| Notification |  |
| Error |  |
Press button (for 2 seconds) to enter menu mode.
Select [5. Adjust Brightness] then press button.
| 5. Adjust Brightness | 1. Status LED | Adjusts status LED brightness |
| 2. Inside LED | Adjusts inside LED brightness | |
| 3. Pointer | Adjusts focus laser pointer brightness |
Select [1. Status LED] then press button.
Adjust the brightness using the (Direction X) buttons.
¶ 7. Switching Tools
Do not let any of your body parts or any foreign objects get caught in the machine during operation.
The tools of the machine are sharp, and may cause serious physical injury.
Please wear safety glasses during engraving process for safety.
Debris like metal chips and dusts may cause serious eye injury if they get stuck in the eye.
¶ • Spindle
| Name | Picture | Quantity | Usage |
| T-wrench (2mm) |
 |
1EA | Tool for tightening/unscrewing of bolt. |
As shown below, insert the 2mm wrench into the fixing bolt. Turn the wrench to the left to unscrew bolt. To prevent the tool from falling to the floor, grab tool with your hand then pull it out. Once the tool is removed, replace it with a new tool then secure it using a wrench for tightening bolts. ※See package contents
When unscrewing the tool fixing bolt, hold the tool with your hand while unscrewing to avoid the bolt from dropping on the floor.