¶ Contents
- 1. Safety Precautions for Electrical System
- 2. Safety precautions for installation
- 3. General precautions
- 4. Safety precautions for using the machine
🔹 Read and follow the instructions carefully for safe use of the machine.
🔹 Failure to follow safety precautions may result in injury and/or machine damage.
🔹 Intended use: MAGIC-E3 is intended for engraving.
- Please follow the necessary safety precautions to prevent injury and/or machine damage.
- Please read carefully and understand the instructions below for proper and safe use of the machine.
 |
Failure to follow these instructions may result to machine damage. |
 |
Failure to follow these instructions may result to physical injury or harm. |
¶ 1. Safety Precautions for Electrical System
| Safety Precautions for Electrical System | |
|---|---|
|
Do not use a damaged power cord or a loose electrical outlet. This may cause electric shock or fire. |
|
Do not plug in two or more devices in a single outlet simultaneously. Overloading your plug sockets may lead to overheating which may cause fire. |
|
Do not pull a plug by the cord. Do not grab a plug with wet hands. This may cause electric shock and burns. |
|
To disconnect the AC adapter from the product, first Turn off the machine and then unplug the AC adapter. |
|
If smoke comes out of the machine, switch off the machine immediately. Do not attempt to repair and/or disassemble the machine, contact our authorized technical support for immediate diagnosis and repair. |
|
This machine is designed to operate on a power supply of 100 to 240 volts. The device will not work correctly if you use a non-AC power source. |
|
Unplug the machine when not in use |
|
Plug the machine into a grounded outlet only. The machine may fail if plugged into an ungrounded outlet, causing property damage, physical injuries, electric shock or fire. |
¶ 2. Safety precautions for installation
| Safety precautions for installation | |
|---|---|
|
Place the machine on a firm, flat, and level surface. If not properly installed, the machine may fall, causing injury, electric shock, or fire. |
|
Do not place any foreign objects or fire hazards on the machine. Never place the machine near or above heating devices or flammable materials. |
|
Do not use the machine if there is smoke, moisture, oil, dust, or water where it is installed. This may cause electric shock or fire. |
|
When installing the product, make sure there is enough space at the back for proper ventilation. If you don't, the product might not work right or get damaged. |
¶ 3. General precautions
| General precautions | |
|---|---|
|
Keep the machine out of children's reach. Risk of serious injury. |
|
Do not spill water or any liquids on the machine. This may cause machine failure, electric shock, or fire. If any liquids or foreign objects get inside the machine, the machine may vibrate excessively and fall, causing injury. |
|
If the product is used in a manner that does not comply with the specified regulations, the product warranty may become invalid. |
|
Check that the product operates correctly before use. |
|
Keep the machine at room temperature. If the temperature drops below freezing, the machine may not work properly. |
|
Use the machine properly and strictly follow all safety precautions. We will not be held responsible for any damage or injury caused by mishandling, misuse, or poor care. |
|
Minor scratches may occur during production. This is not a product defect and is not subject to return or exchange. |
¶ 4. Safety precautions for using the machine
|
 |
Protect your hands, wrists and fingers. Do not let any of your body parts or any foreign objects get caught in the machine during operation. The tools of the machine are sharp, and may cause serious physical injury. |
|
 |
Please wear safety glasses during engraving process for safety. Debris like metal chips and dusts may cause serious eye injury if they get stuck in the eye. |
|
 |
Laser Radiation Avoid eye or skin exposure to direct or scattered radiation. |
|
 |
When removing chips or metal dust from inside the machine, do not blow with your mouth or use compressed air. Always use a vacuum cleaner. Scattered chips or dust can cause severe eye injuries and respiratory problems. |
|
Do not leave the machine unattended during operation. Remain attentive and avoid any activity that diverts attention while the machine is running. |
|
|
Keep hands and fingers away from the moving parts during operation. Getting caught in the machine's axis may cause serious injury. | |
|
Do not disassemble or modify the internal components of the machine. This may result in fire, electric shock, or equipment failure. For inspection, adjustment, or repair, please contact the place of purchase or an authorized authorized technical support. |
|
|
Use a dust collector to remove particles produced during the engraving process. Metal chips and dust may cause serious eye injury if they enter the eye, and respiratory problems if inhaled. |
|
|
Avoid using materials that may get caught or jammed in the machine. The engraving and cutting performance and quality of the machine may vary depending on the materials used. |
|
|
Do not lean on the product or load it with heavy objects. | |
|
Ensure adequate ventilation when operating the machine. | |
|
Depending on the material (pure silver), there may be differences in performance and quality in terms of marking and cutting. | |
¶ PROPER MACHINE DISPOSAL
 |
The machine contains valuable raw materials and electronic components which must be properly disposed of in equipment disposal containers.
According to European guidelines on proper equipment disposal: |
¶ Laser Specifications
The machine utilizes red laser ‘CLASS 2’ as a guide laser.
- CLASS 2: Class 2 laser is a relatively weak laser that is considered safe for normal operation Its visible beam does not cause any harm or damage on a person’s eye unless deliberately stared into it. It is not a skin or materials burn hazard as well.
| Class | Class 2 |
| Power | <1mW |
| Wavelength | 650nm |